TX6000 6 Channel Mic/Line Mixer

| Specifications | Architectural Specifications |

Description
The TX6000 is a high specification, single rack space, 6 channel mic/line mixer suitable for desk or rack mounting. The mixer is designed to operate from both AC mains power as well as 24 volts DC.
Inputs
Six dual mic/line inputs are provided. The mic inputs are active balanced and feature 3 pin XLR female sockets. Each channel also includes dual female RCA line/aux sockets.
Outputs
The TX6000 features a balanced line output via a 3 pin XLR male socket. A mono tape output is also available via dual female RCA sockets. A 1/4" mono headphone socket is included on the front panel.
Controls
Front panel controls include a master output level control plus overall bass and treble controls. Individual channel level controls are provided for all six inputs.
VCA Control
The master volume can be controlled remotely. External VCA control would normally be via a pot connected to a two wire rear panel barrier strip.
Metering
A 7 segment LED meter is provided for the master output. A power "on" LED is also included.
Muting
Muting is available via the optional VOX operated plug-in TX3010 or TX3014 precedence cards. The TX3010 provides priority from channel 1 over all other channels. The TX3014 provides two levels of priority. Channel 1 is the master mute channel and overrides channels 2-6, whereas channels 2 will mute channels 3-6 only.
Tone Generators
The ATC5488 is an optional plug-in accessory providing 4 tones (Bell, Pre-Announce Chime, Alert and Evacuate). The ATC5488 plugs into the main board via a 7 pin connector. Activation wires can be fed through a rear panel slot below the 24V DC connector. Each tone can be activated by a simple contact closure.
Phantom Power
Phantom power (18V DC) is provided on all mic inputs.

TX6000 Specifications
Frequency Response 50Hz - 15kHz (± 3dB)
Total Harmonic Distortion Less than 0.08% @ 1kHz
Signal To Noise Ratio -78dB (all channels at centre position)
Tone Controls Bass @ 100Hz, Boost +12dB, Cut -12dB; Treble @ 10kHz, Boost +9dB, Cut -9dB
Inputs 6 dual mic/line. The mic inputs are active balanced with 3 pin XLR female sockets (200-600 Ohms). Maximum input level is 100mV. The line inputs are dual female RCAs (47K Ohms). Maximum input level: 2.5V/10V
Input Sensitivity Mic: 0.6mV @ 200 Ohms; Line: 150mV @ 47K Ohms
Phantom Power 18V DC available on all mic channels (overall internal on-off link)
Outputs Master output is via a 3 pin male XLR socket (1.5V @ 600 Ohms). Maximum output level: +20dB. Mono headphone output via 1/4" socket (3.5V @ 600 Ohms). Mono tape output via dual female RCA connectors (700mV @ 10K Ohms)
Controls Level control per channel, Overall bass & treble controls, Master level control
Indicators Power "on" LED, 7 segment LED meter on master output
Power Sources 120VAC 60Hz 3 pin IEC connector; 24VDC via 2.1mm DC socket
Power Consumption 7 vA
Dimensions/Weight 1.75" H x 19" W x 9.85" D (Chassis Dimensions Only). 6.6lb

Architectural and Engineering Specifications
The mixer shall have six dual mic/line inputs. The microphone inputs shall be active balanced and feature 3 pin female XLR sockets. The line inputs shall feature dual female RCA sockets. Overall bass and treble controls shall be provided with front panel access. They shall provide 12dB cut or boost at 100Hz and 9dB cut or boost at 10kHz. The master section shall include a master level control and a 7 segment output level LED meter. The master output shall be via a balanced 3 pin XLR male socket. The tape output shall be via dual female RCA sockets whilst a 1/4" headphone socket shall be provided on the front panel for monitoring purposes. The mixer shall have facilities for plug-in muting cards as well as a 4 tone generator card. The mixer shall be of high quality, suitable for both live and commercial applications. It should have ample headroom and a frequency response of no less than 50Hz - 15kHz (±3dB). Total Harmonic Distortion shall be no more than 0.08% at 1kHz. The S/N ratio shall be -78dB or better. Phantom power shall be available to all microphone inputs and shall be switchable via an internal link. The unit shall be packaged in a one rack unit rugged metal chassis suitable for desk or rack mounting. The mixer shall be an Australian Monitor Installation Series model TX6000.

| Black & White Spec Sheet 80K | Colour Spec Sheet 212K | Contact Australian Monitor for more info |

| Top of Page | Return to Home Page |

TX8000 8 Channel Mic/Line Mixer

| Specifications | Architectural Specifications |

Description
The TX8000 is a high specification, single rack space, 8 channel mixer suitable for desk or rack mounting. The mixer is designed to operate from both AC mains power as well as 24 volts DC.
Inputs
The TX8000 has six dual mic/line inputs and two mic only inputs. The mic inputs are active balanced and feature 3 pin XLR female sockets. The line inputs feature dual female RCA sockets. Each channel includes front panel, screwdriver adjustable treble and bass controls. Individual gain can be set-up for each channel via an internal trim control.
Outputs
The TX8000 features a balanced line output via a 3 pin male XLR socket. A mono tape output is also available via dual female RCA sockets. A 1/4" headphone socket is included on the front panel.
Controls
Front panel controls include the master output level plus individual channel level controls. Each channel also includes front panel recessed screwdriver adjustable treble and bass control controls. An internal trim control is also provided for every channel.
VCA Control
The master volume can be controlled remotely. External VCA control would normally be via a pot connected to a two wire rear panel barrier strip.
Metering
A 7 segment LED meter is provided for the master output. A power "on" LED is also included.
Muting
Muting is available via the optional VOX operated plug-in TX3010 or TX3014 precedence cards. The TX3010 provides priority from channel 1 over all other channels. The TX3014 provides two levels of priority. Channel 1 is the master mute channel and overrides channels 2-8, whereas channel 2 will mute channels 3-8.
Tone Generators
The ATC5488 is an optional plug-in accessory providing 4 tones (Bell, Pre-Announce Chime, Evacuate and Alert). The ATC5488 plugs into the main board. Connection wires can be fed through a rear panel slot below the 24V DC connector. Each tone can be activated by a simple contact closure.
Phantom Power
Phantom Power (18V DC) is provided on all inputs.

TX8000 Specifications
Frequency Response 40Hz - 15kHz (± 3dB)
Total Harmonic Distortion Less than 0.05% @ 1kHz
Signal To Noise Ratio -76dBV (all channels at centre position)
Tone Controls Bass @ 100Hz, Boost +12dB, Cut -12dB; Treble @ 10kHz, Boost +9dB, Cut -9dB
Inputs 8 inputs, 6 of which are dual mic/line. The mic inputs are active balanced with 3 pin XLR female sockets (200-600 Ohms). Maximum Input Level is 300mV. The line inputs are dual female RCAs (47K Ohms). Maximum Input Level is 10V. The last two inputs are balanced mic only.
Input Sensitivity Mic: 0.6mV @ 200 Ohms; Line: 150mV @ 47K Ohms
Phantom Power 18V DC
Outputs Master Output, 3 pin XLR male socket. (1.5V @ 600 Ohms). Maximum Output Level: +20dB. Mono Headphone Output, 1/4Ó socket (3.5V @ 600 Ohms). Mono Tape Output, dual female RCA connectors. (700mV @ 10K Ohms)
Controls Level Control per channel, Internal Trim Control per channel, Recessed Treble and Bass Controls per channel, Master Level Control
Indicators Power "on" LED, 7 segment LED meter
Power Sources 120VAC 60Hz 3 pin IEC connector; 24VDC
Power Consumption 7 vA
Dimensions/Weight 1.75" H x 19" W x 9.85" D (Chassis Dimensions Only). 6.6lb

Architectural and Engineering Specifications
The mixer shall have six dual microphone/line inputs and two dedicated microphone inputs. The microphone inputs shall be active balanced and feature 3 pin female XLR sockets. The line inputs shall feature dual female RCA sockets. Each channel shall include tamper resistant treble and bass controls. An internal trim pot shall also be included for all channels. The equalisation per channel shall provide 12dB cut or boost at 100Hz and 9dB cut or boost at 10kHz. The master section shall include a master level control and a 7 segment output level LED meter. The master output shall be a balanced 3 pin XLR male socket. The tape output shall feature dual RCA female sockets. A 1/4" mono headphone socket shall be included for monitoring. The mixer shall have facilities for a plug-in dual level muting card, as well as a 4 tone generator card. The mixer shall be of high quality, suitable for both live and commercial applications. It should have ample headroom and a frequency response of no less then 40Hz - 15KHz (±3dB). Total Harmonic distortion shall be no more than 0.05% at 1kHz. The S/N ratio shall be -76dBV or better. Phantom Power of no less than 18V DC shall be available on all microphone inputs. An internal switch to disable the phantom power shall also be included. The unit shall be packaged in a metal chassis suitable for desk or rack mounting. The mixer shall be an Australian Monitor Installation Series model TX8000.

| Black & White Spec Sheet 80K | Colour Spec Sheet 224K | Contact Australian Monitor for more info |

| Top of Page | Return to Home Page |

TX8201 8 Channel Stereo Mic/Line Mixer with Direct Outputs

| Specifications | Architectural Specifications |

Description
The TX8201 is a high performance 8 channel stereo mixer suitable for desk or rack mounting.
Inputs and Outputs
The TX8201 has six active balanced mic/line inputs and two stereo line inputs. Each channel features recessed treble, bass and pan controls. Mic/Line level can be adjusted per channel via a dip switch. All mic and line input connections are via 3 pin XLR female sockets, and all stereo line input connections are via dual female RCA sockets. Both the Left and Right outputs are balanced and feature 3 pin male XLR sockets. A stereo tape output using dual female RCA sockets is also provided. A 1/4" stereo headphone socket is included on the front panel. The rear panel includes a terminal block for activation of the Tone Generator. The first six channels feature a line level direct output which can be used to feed additional amplifiers, mixers or recording devices. An internal jumper allows the first six inputs to be removed from the master left/right outputs whilst still retaining their direct output function.
Controls and Metering
Front panel controls include Master Left and Right Outputs plus individual channel level controls. Each channel also features a recessed, screwdriver adjustable treble, bass and pan control. A four position dip switch (mic/line, phantom power, routing) is provided for the first six channels. A 7 segment LED meter is provided for both the Left and Right Outputs. A power "on" orange LED is part of the LED meter.
VCA Control
The master volume can be controlled remotely. External VCA control would normally be via a pot connected to a two wire rear panel barrier strip.
Muting
Muting is standard on the unit for channels one and two. Both channels have equal priority and will mute channels 3-8 when signal is present. The muting function can be disabled by moving an internal jumper.
Tone Generators
Bell, Pre-Announce Chime, Evacuate and Alert are included in the unit. Each tone can be activated by a simple contact closure using the rear panel terminal block.
Phantom Power
Phantom Power (15V DC) is available on all mic inputs and can be disabled if need be via a dip switch.

TX8201 Specifications
Frequency Response 50Hz - 15kHz (± 3dB)
Total Harmonic Distortion Less than 0.1% @ 1kHz
Signal To Noise Ratio -74dBV (all channels at centre position)
Tone Controls Bass @ 100Hz - Boost +12dB, Cut -12dB; Treble @ 10kHz - Boost +10dB, Cut -10dB
Inputs 6 active balanced mic/line inputs with 3 pin XLR female sockets (200 - 600 Ohms). Maximum Input Level is 500mV. 2 Stereo Line inputs with dual female RCAs (47K Ohms). Maximum Input Level is 1.5V.
Input Sensitivity Mic: 1mV @ 200 Ohms; Line: 150mV @ 47K Ohms
Phantom Power 15V DC on all mic channels (switchable)
Outputs Left & Right Master Outputs, 3 pin XLR male sockets. (1.5V @ 600 Ohms.) Maximum Output Level: +20dB Stereo Headphone Output, 1/4" stereo socket. (3.5V @ 600 Ohms) Stereo Tape Output, dual female RCA connectors. (400mV @ 10K Ohms). Six direct line level outputs (600mV @ 10K Ohms)
Controls Level Control per channel, Recessed Treble, Bass and Pan Controls per channel, Left and Right Master Level Controls
Indicators Power "on" orange LED, 7 segment LED meters for both L and R outputs
Power Source 120VAC 60Hz 3 pin IEC connector
Power Consumption 7 Watts Dimensions/Weight 1.75" H x 19" W x 9.85" D (Chassis dimensions only). 8.8lb

Architectural and Engineering Specifications
The mixer shall have 6 balanced mic/line inputs and 2 stereo line inputs. The mic/line channels shall be balanced and feature 3 pin female XLR sockets. The stereo line channels shall have dual female RCA sockets. Each channel shall include tamper resistant treble, bass, and pan controls. The first six channels feature a line level direct output which can be used to feed additional amplifiers, mixers or recording devices. An internal jumper shall allow the first six inputs to be removed from the master left/right outputs whilst still retaining their direct output function. The equalisation per channel shall provide 12dB cut or boost at 100Hz and 10dB cut or boost at 10kHz. The master section shall include individual level controls for both the Left and Right outputs and shall also include two 7 segment output level LED meters. The master outputs shall be balanced 3 pin XLR male sockets, and dual RCA female sockets for the stereo tape output. A 1/4" stereo headphone socket shall be included for monitoring. The mixer shall include muting card, as well as a 4 tone generator. The mixer shall be of high quality, suitable for both live and commercial applications. It should have ample headroom and a frequency response of no less than 50Hz - 15kHz (±3dB). Total Harmonic distortion shall be no more than 0.1% at 1kHz. The S/N ratio shall be -74dBV or better. Phantom Power of no less than 15V DC shall be available on all microphone inputs. An internal switch to disable the phantom power on any of the mic/line channels shall also be included. The unit shall be packaged in a rugged 1RU metal chassis suitable for desk or rack mounting. The mixer shall be an Australian Monitor Installation Series model TX8201.

| Black & White Spec Sheet 88K | Colour Spec Sheet 232K | Contact Australian Monitor for more info |

| Top of Page | Return to Home Page |